Posted on

cbd oil home

After the time is up, pour the oil and flower through some cheesecloth (coffee filters will work in a pinch) to strain off the plant matter, leaving behind the CBD-rich oil. If you’re using cheesecloth, be sure to squeeze out all the oil you can from the bundle of plant matter—a potato ricer is super handy for this, but not necessary if you don’t mind using a little elbow grease.

The oil can also be applied directly to the skin for topical pain relief, added to your favorite body care products before application, or incorporated into your diet a few drops at a time. Its uses are just as versatile as the CBD you would have bought from a retailer, only it’s custom-designed by you, for you.

2-3 hours is sufficient time for the CBD to dissolve into the oil; though, there is no harm in going longer. You don’t need to monitor the oil too closely: checking in every half hour or to stir and monitor its color should be sufficient. When it’s a deep, earthy brownish-green, you’ll know it’s ready.

Step 3: Extraction

However, if you don’t reside in a state where you can buy your hemp flower from a trusted, licensed professional, Farm Bill-compliant hemp flower is legal for purchase, though it’s not available over the counter in most places.

It might seem not very easy, but we promise you, you can do this! Here, we’ll discuss the science of cannabinoid extraction and showing you that making CBD oil at home does not have to be as intimidating as it may seem.

Discard the leftover starting material; its work here is done. You can then place the oil in a bottle or mason jar and store it in a cool, dry place away from the sun and other light sources.

Once you’ve decarbed the starting material, mix your carrier oil and decarbed flower into the top of a double boiler and place over a pot of simmering (not boiling!) water. Low heat on most stovetops should be sufficient to get the water bath hot enough to extract the CBD without risking scorching the oil. You can also use a crockpot as an alternative to a double boiler.

Next, you’ll need to separate the CBD-rich alcohol extract from the plant matter. Strain the solution through a piece of cheesecloth or a fine sieve into a bowl below. You’ll notice that the alcohol has a dark green colour to it. Repeat the process above with fresh alcohol a few more times to get the most out of your buds or trim. Eventually, the extract will start appearing more clear in colour, a sign that the material is now spent.

Pour the alcohol extract into the stainless steel bowl/top of the double boiler and apply gentle heat. High-proof alcohol is highly volatile and will evaporate at a low temperature. Keep the heat down and turn the heat on and off where necessary. It’s important to carry out this process away from any naked flames and ideally under an extractor fan or outdoors. The vapour produced when the alcohol evaporates is highly flammable and poses a real fire hazard.

Place your decarbed buds or trim into the mixing bowl and pour in enough alcohol to completely submerge the plant matter. Use the wooden spoon to stir the material for 5–10 minutes. During this time, the alcohol will pull out the desired constituents such as CBD and terpenes. Stirring will help to accelerate the process and dislodge the trichomes that produce these substances.

STEP 2

The first requires using food-safe alcohol to extract CBD from hemp plant material. The second, which has become popular due to the gentle process involved, utilises natural plant oils to extract CBD. Hemp seed, olive, and coconut oils are popular choices here and are fairly effective solvents.

Making DIY CBD oil at home is pretty easy if you have the right ingredients. It will by no means be as powerful or as potent as professionally extracted and produced CBD oil (which is actually quite an in-depth and complicated process), but with a few easy steps, you can still harness some of the power hemp has to offer.

Now it’s time to set up the double boiler. If you don’t have a setup like this already, an easy makeshift option is to fill the bottom of a saucepan with water, then place a stainless steel bowl into the saucepan that fits snugly, but doesn’t touch the bottom of the pan.

To begin, you need to ensure your plant matter is decarboxylated. To do so, grind it up until it has a fine even consistency, and place on a baking tray lined with parchment paper. Place it in a preheated oven at 110ºC (225ºF) and allow to cook for one hour.